Starter Clicks But Engine Does Not Turn Over – Tech in Trunk?

If the car’s starter clicks and the engine does not turn over, this could be caused by several things. The most common cause of clicking when the car is being started is a low battery. Most people would assume that the starter is bad if it only clicks, but low-voltage can cause the starter to make this sound.

The battery is the heart of the starting and electrical system. If the battery has been drained or has a weak cell, this can cause the starter to only click. Many times the battery could just been drained due to a door left slightly open, making the dome light stay on. Other times a vanity light or a phone charger could be left on. During my time as a master auto technician, I’ve had a trustworthy co-worker close me up in the trunk so I could make sure the trunk light went off when the trunk was closed!

In order to test the battery it must have a good charge. If the battery is not charged completely the tester will indicate that it needs to be charged before testing can proceed. The first step when checking the starter and electrical system is to make sure the battery is in good condition. Most parts stores will check batteries for free. Once it’s determined the battery is good the rest of the system can then be checked. Loose or corroded connections can also cause a clicking and for the car not to start.

Starter

The starter solenoid on many Ford vehicle’s is on the inner fender well, on most other vehicles the starter solenoid will be mounted on the starter. The clicking that is heard many times is the solenoid. But low-voltage either from a drained battery, bad battery or poor connections can cause this. Most of the time if the vehicle can be jump-started the starter is okay. This would also indicate that the connections to the starter are good.

Alternator

Once the vehicle is running the alternator output can be checked. If the alternator is not charging the battery, it will be drained during the process of starting the car and driving. When the alternator is checked, the voltage and amperage output can be measured. Also the diode pattern will be checked to make sure the alternator won’t drain the battery when the engine is turned off. In the past do-it-yourselfers could disconnect the battery while the vehicle is running to check the alternator, if the car kept running the alternator was good. Doing this on computerized vehicles can be harmful. If the battery is disconnected while a computerized vehicle is running the alternator output can increase sharply allowing excess voltage to spike the computer.

Battery

When purchasing a replacement battery the cold cranking amps required for the vehicle should be checked. It’s best to purchase a battery with more cold cranking amps than the minimum required. Also when purchasing a battery you should consider if you want maintenance free or not. If the battery is hard to access or has a cover then a maintenance free battery is preferred. For instance on some Chrysler Sebrings and Chevrolet Corvettes the battery is located behind an inner fender and on a Chevrolet SSR. the battery is located underneath the bed where the spare tire would normally go. If installing the battery yourself be sure to notice which side is positive and negative in case you were sold the incorrect battery.

Terminals

The terminals should be free of corrosion and should tighten up well. Sometimes especially on import vehicles the battery terminals will be very thin and can have hairline cracks causing a poor connection. Avoid forcing the battery terminals on by tapping them. The battery casing can be damaged causing a leak, if the battery acid seeps out it can cause fast corrosion. If the battery terminal bolts will not tighten, then replacing the terminals is recommended. When the connections are tight you should not be able to twist them by hand.

Energy Healing and the Sacred Art of Transmission

In a sense, we are all transmitting, or broadcasting energy all of the time via our thoughts, feelings and beliefs, as everything is energy and has frequency. Yet I wanted to go deeper here and share with you what I know to be possible, which I am referring to as the “sacred art of transmission” as it is a much more powerful, precise and rare spiritual and healing gift.

It is the ability to transmit spiritual, healing, and intuitive awakenings through look, touch, voice, or even mere presence. It has been over twenty years, but I will never forget my earliest memories of energy transmissions. While some happened through my spiritual teachers, many of them occurred during Reiki healing sessions, and then in teaching and attuning others to this awesome healing art.

Reiki Energy Healing Attunements are Transmissions

After I met my first spiritual teacher, I decided to take a Reiki workshop even though I had never experienced it myself. I was just so curious and my colleague had told me of her experience awhile back, but at that time I was not open, as I had no mental “box” to put it in and kind of shelved the whole concept.

I am so grateful I did. Because I noticed that while there were many great and wise people I knew who were meditating also with the same Master, and most for much longer than me, it was not common for anyone but the energy healers to expect to be able to transmit this potent energy and spiritual space. It was clearly a level of empowerment that I came to appreciate only much later. And it had to do with owning the ability to transmit energy, not just to sit in the energy.

In Reiki Level 1 there are 4 initiatory attunements, which I couldn’t possibly comprehend at that time. Reiki attunements are initiations or transmissions of energy that open the healing channels or energy pathways within everyone.

Yet I now come to realize that the Reiki Master is passing down the ability to awaken or open the healing channels that lie dormant within us all, through these specific attunements. In this instance, everyone else in class was tingling, but I feared I was a Reiki “dud” when we began to practice on each other, and everyone else’s hands were tingling, and I got nada, bupkis.

Until we got to the final two attunements. And something DEFINITELY happened. I actually heard and felt a spirit man initiating me, in addition to the woman teaching the class. When I asked who it was, I got that it was the founder, Dr. Mikao Usui, himself. I asked if he did all of the attunements with her, and she looked stunned. I can only guess that was not everyone’s experience.

Then it began happening: not from me but through me…

I have taught students, who have supposedly already taken Reiki classes with another teacher, and they were very surprised that they felt such tangible energy flow, or experienced such deep meditation states, expansion, and 3rd eye intuitive openings. I was surprised that they didn’t experience that with other teachers. It pains me, but there seem to be many people now teaching a much diluted version of what I received.

It is way more than just intention. It is more like you begin to embody the universal life energy. I now have two decades of validation that direct transmission is happening through me, and not just in Reiki attunements or private sessions. It begins to flow through you like water… and not just via the hands. One Reiki student was walking with me and we stopped at a small waterfall flowing into a pond. She gasped, and said that something was coming out of my eyes; a light, and it felt just like a healing session.

Another time, I met with a new neighbor and she was describing her chronic back pain. I felt deep compassion for her and wanted to help in some way, but it felt too early in the conversation to suggest a Reiki session. But she immediately felt relief, and asked “are you doing that thing you do, cuz my back feels better and better.”

Over time, the knowing what is possible, turns to probable. Now, with very little effort on my part I can align and focus my eyes, my feet, my heart, my thoughts and healing happens, calm serene stillness descends, light radiates. I used to be shy about stating these things, feeling like it was ego. But now I know I must tell you all what is possible for you, just as it became possible for me. I see my students stepping into this mind-blowing reality that they, too can transmit healing energy. There is nothing that delights me more!

Metal Fabricators – A Boon to Metallurgy

Every now and then, we keep hearing of the term ‘steel metal fabrication’. But have you ever wondered what metal fabricators are used for? This article will give you a glimpse into the world of fabrication and how it is fast becoming the next big thing in metallurgy.

As the term suggests, fabrication means constructing metal structures with the aid of cutting, bending and assembling. The processes of shearing, sawing and chiseling are utilized for the cutting part. The bending of the metal is done by hammering or by using press brakes which can be done both manually and by using power. Last but not the least, the assembling process is conducted by welding, and then attaching them with adhesive, riveting or threaded fasteners.

The metals which are essentially required for steel fabrication are structural steel and sheet metal. Besides these, one also requires welding wires, flux and fasteners to attach the metal cut pieces. For the process of metal fabrication both human labor and automation is required. The final products are sold in shops which also specialize in metal stamping forging and casting.

Steel metal fabrication is used in various segments and we will explore various areas where it is extensively used. It is generally used in fabrication and machine shops which basically deal with metal assembly and preparation. In these shops, metals are dismantled and cut and they also deal with machines and tools. Black smiths also use the process of metal fabrication and so do welders to create weldments. Boiler makers and mill wrights who set up saw and grain mills extensively also extensively make use of metal fabricators. The steel erectors or iron workers use prefabricated segments in order to initiate the structural work and then they are transported to the work site by means of truck and rail where they are installed by the erectors.

The technique of metal fabrication involves changing metals from one form to another. There are various classes of the fabrication process including structural, architectural, ornamental, recreational and artistic. If you are interested in fabricating a metal you have to determine whether it contains iron or is ferrous or whether it is non-ferrous. You have to choose the appropriate welding instrument which will correspond to the metal which you are going to fabricate. Before beginning the work you have to prepare a well-laid plan which includes the details relating to rolling, bending and bolting metal pieces together to create a highly specialized structural piece of work.

The Avian Plight

In 1997, the world’s attention was caught by an alarming passage of Avian influenza from birds to humans in Hongkong. All chickens and ducks were killed upon the order of the Hongkong government to contain the spread of the deadly H5N1 virus.

Avian influenza or more commonly called as bird flu is an infection caused by avian (bird) influenza (flu) viruses. All birds naturally have these influenza viruses in their bodies. Wild birds have these viruses in their intestines but their bodies do not get infected or damaged by them. When passed on domesticated birds, avian influenza can cause sickness and death. Chickens, ducks, and turkeys are mostly hit by the   transmission  of avian flu among birds. Infected domesticated birds can pass on the virus to humans when they are eaten or consumed. *Migratory birds* infected with avian flu also become agents of viruses’ transfer from one place to another.

H5N1 carrier birds pass on the virus to other birds through their saliva, nasal excretions, and feces. Birds get infected when they come in contact with these contaminated excretions even by just staying on a surface or ground where virus carriers have stayed. Cages, dirts, water, feeds, infected waterfowl or other poultries that have been exposed to the virus are the common sources of infection among domesticated birds.

Two forms of bird flu exist among domesticated poultries infected with avian influenza viruses. The low pathogenic form is almost invisible and undetected for it causes only very mild symptoms that can be mistaken as non-avian flu effects. Manifestations of low pathogenic avian flu infection include low egg production or ruffled feathers. The second form of avian flu is the high pathogenic avian flu disease. This form leads to multiple organ failures and damages among infected birds. About 90 to 100 percent of birds infected with this form die within two days upon contamination. The spread of this form of avian flu is more rapid among birds in flocks.

Albeit basically a matter among birds, humans are also susceptible to bird flu or avian flu infection. The first known cases of humans getting infected with bird flu happened in Hongkong in 1997. 18 people were recorded to have acquired respiratory illnesses after having contacted infected surfaces from poultry farms, the infection claimed six lives.

The virus’ passage to humans that happened in Hongkong caused a global alarm. Health institutions worldwide raised concerns that the avian flu might be as damaging as the pandemic of flu that claimed about 20 million lives back in 1918. Reasonable enough, the fear and alarm are worth noting. What is essentially fearful is the idea that humans can be infected and actually die from a virus that is basically existing among birds only. The premise the Hongkong incident set is that the virus is mutating into something deadly for humans.

As of 2005, worldwide coordinated statistics recorded a number of 130 people having been infected of avian flu of which 67 have already died. In recent years, cases of human infection have been high in Asian countries. The World Health Organization believes that Asia is at higher risks since people live in close distance with domesticated birds like chicken and ducks. Animal domestication and poultry raising are common among many Asian countries who are agricultural by nature. What worries many is the common fact that humans have little or even a lack of immunity to the virus known to be infecting only (until the 1997 Hongkong incident) the birds.

An even higher cause of alarm has been found in recent studies on the H5N1 virus. Recent researches have shown that H5N1 strains have become more deadly among chickens and mice. This mutation is also found to be making cats or feline susceptible to the infection. H5N1 is also found to be resistant to some of the drugs used to treat flu (such as amantadine). New strains of the virus are also said to be possibly emerging especially in Asian countries.

What is now being focused on by scientists and health experts around the world is the prevention of human-to-human  transmission  which is believed to be the possible case that happened in Thailand in 2004. If it becomes widespread, human-to-human  transmission  is believed to be harder to contain that bird-to-human  transmission . Experts say that the virus’ continual change will make it hard for the human body to naturally develop immunity against the infection. The H5N1 virus is found to be changing over time through the changes happening in their structure called antigenic drift and antigenic shift. This continual change of the virus disables the immune system to respond accordingly whenever the flu virus enters the body. The only possible solution seen by experts is for infection-prone people to have a yearly immunization with up-to-date anti avian virus strains. But the big problem is, until now there is no medical treatment available to combat the H5N1 virus, making the yearly immunization update a far-fetched option.

Dirofilariasis – The Deadly Heartworm in Dogs

When a dog is suffering from heartworm, it means that they are infected with a roundworm commonly known as heart worm. The organism is actually Dirofilaria immitis, a parasite. This worm is transmitted by mosquitoes and will infect your dog’s blood, heart and lungs. Left untreated, the disease is fatal.

Causes

Heartworms are spread through mosquitos that carry the infective heartworm larvae. The larvae enter the dog’s body through the mosquito bite wound and travel through the dog’s body to the heart. This process will take approximately six months.

Once the heartworms are living inside your dog, the adults will release immature heartworms (microfilariae) into the bloodstream of the dog. When a mosquito bites an infected dog, it will become a carrier of these microfilariae and infect the next dog it bites.

If a dog lives in a high risk area for heartworm, without preventative treatment it will almost certainly contract heartworm disease. Although heartworm is mainly endemic in tropical and subtropical areas, it is not limited to these areas. Heartworm has been identified in all 50 US states and is found worldwide.

Symptoms of Heartworm

Heartworm disease can be diagnosed by your veterinarian through a blood test. There are three classes of heartworm, and the symptoms vary from no visible symptoms to extreme ill health. It is difficult for a dog owner to identify heartworm in their pet.

The symptoms of heartworm include but are not limited to an occasional or more regular coughing, reduced canine activity or an intolerance to exercise, anaemia, fainting, chronic heart failure, labored breathing and high blood pressure.

The severity of heartworm disease will depend on the severity of the infestation, the duration of the disease and the response of the dog. All dogs are different in the way their bodies cope with the heartworm infestation.

Diagnosis

If your vet suspects your dog may have heartworm they can conduct a blood test, carry out an electrocardiograph (can reveal heart rhythm disturbances), a urine analysis or x-rays. They are looking for damage to or enlargement of the heart and associated arteries.

Treatment

Initially your dog will be hospitalized, and receive a dose of adulticide which will kill the adult heartworms. Depending on the severity of the infestation your dog may need to be hospitalized for a longer period. In some cases surgery may also be required to remove adult worms from the heart and jugular vein.

After the adult worms have been killed, treatment must be ongoing with a monthly dose of prophylaxis to kill eggs and larvae which have not been killed by adulticide.

You should be aware that the treatment for heartworm can be deadly. Even mild to moderate cases of heartworm will have a considerable impact on your dog. It is not an easy treatment for your dog, and should not be considered light heartedly.

Prevention

Heartworm disease is completely preventable through a regular dose of prophylaxis which is a preventative heartworm medication. Your veterinarian will be able to assist you with the appropriate medication and dosage to suit your dog.

If your dog does contract heartworm and has been successfully treated, you should take care to administer the monthly dose of prophylaxis as advised by your vet – reinfestation can easily occur especially in high risk areas.

What is CNC?

CNC is the acronym of Computer Numeric Control and it is often associated with plasma cutting as in CNC plasma cutting. A plasma cutting unit that is controlled by CNC is controlled by a computer. There are two basic classes of controls, industrial PC-based control systems and hobbyist/artisan PC-based control systems. The industrial CNC systems, such as the ones produced by Hypertherm or Burny, are robust enough to stand up the harsh production environments. They have a touch screen that can be housed inside of a heat shield for additional protection. The industrial CNCs are very costly, but they come highly recommended for any application because they are not vulnerable to typical PC problems meaning they have very little down time. Due to the high cost you will not often find industrial scale CNCs in a hobbyist’s garage. The artisan and the hobbyist plasma cutter use standard PC-based controls with I/O cards for controlling the plasma systems and the drives. Since these are regular PCs they are prone to an array of computer problems, but none that cannot be fixed.

If you want to use a CNC for your plasma cutting there are some things you will need. You will need a table for the cutting to take place on. On each side of the table you must have a rail that the drives can use to move the plasma systems; we will call this the x-axis. A bridge or gantry must span the table and each end must rest on the rails. The plasma system must be attached to a rail on the bridge which will allow it to move back and forth; the y-axis. Industrial strength set ups us fabricated steel for the construction of the table, rails and bridge. On the other hand, extruded aluminum is used for the hobbyist and artisan CNC plasma cutter set ups. The difference is that the steel is more robust and will withstand constant use whereas the aluminum can only withstand occasional use. If building one of these machines sounds a little scary to you, there are lots of kits that you can buy or you have the option of buying ready built CNC plasma cutters.

If you cruise the web you will be able to find many videos showing CNC plasma cutters in action. It is not the easiest topic in the world to explain and I suggest you check out some videos if you have not seen a CNC plasma cutter before.